View MC10EP89_83910.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10EP89 Coaxial Cable Driver
The MC10EP89 is a differential fanout gate specifically designed to drive coaxial cables. The device is especially useful in digital video broadcasting applications; for this application, since the system is polarity free, each output can be used as an independent driver. The driver produces swings 70% larger than a standard ECL output. When driving a coaxial cable, proper termination is required at both ends of the line to minimize signal loss. The 1.6 (5V) and 1.4V (3.3V) swing allow for termination at both ends of the cable, while maintaining a 800mV (5V) and 700mV (3.3V) swing at the receiving end of the cable. Because of the larger output swings, the device cannot be terminated into the standard VCC-2.0V. All of the DC parameters are tested with a 50 to VCC-3.0V load. The driver accepts a standard differential ECL input and can run off of the digital video broadcast standard -5.0V supply.
http://onsemi.com
8 1 SO-8 D SUFFIX CASE 751
* * * * * * * * * * * *
310ps Typical Propagation Delay 3.0 GHz Typical Toggle Frequency 1.6V (5V) and 1.4V (3.3V) Swing PECL mode: 3.0V to 5.5V VCC with VEE = 0V ECL mode: 0V VCC with VEE = -3.0V to -5.5V Internal Input Resistors: Pulldown on D, Pulldown and Pullup on D Q Output will default LOW with inputs open or at VEE ESD Protection: >4KV HBM, >200V MM New Differential Input Common Mode Range Moisture Sensitivity Level 1, Indefinite Time Out of Drypack Flammability Rating: UL-94 code V-0 @ 1/8", Oxygen Index 28 to 34 Transistor Count = 152 devices
MARKING DIAGRAM
8 HEP89 ALYW 1 *For additional information, see Application Note AND8002/D A L Y W = Assembly Location = Wafer Lot = Year = Work Week
PIN DESCRIPTION
PIN D, D Q0, Q1, Q0, Q1 VCC VEE FUNCTION ECL Data Inputs ECL Data Outputs Positive Supply Negative, 0 Supply
Q0 1
8
VCC
Q0
2
7
D
ORDERING INFORMATION
Q1 3
6
D
Device MC10EP89D
Package SOIC SOIC
Shipping 98 Units/Rail 2500 Tape & Reel
Q1
4
5
VEE
MC10EP89DR2
Figure 1. 8-Lead Pinout (Top View) and Logic Diagram
(c) Semiconductor Components Industries, LLC, 1999
1
December, 1999 - Rev. 1
Publication Order Number: MC10EP89/D
MC10EP89
MAXIMUM RATINGS*
Symbol VEE VCC VI VI Iout TA Tstg JA JC Tsol Power Supply (VCC = 0V) Power Supply (VEE = 0V) Input Voltage (VCC = 0V, VI not more negative than VEE) Input Voltage (VEE = 0V, VI not more positive than VCC) Output Current Operating Temperature Range Storage Temperature Thermal Resistance (Junction-to-Ambient) Thermal Resistance (Junction-to-Case) Solder Temperature (<2 to 3 Seconds: 245C desired) Still Air 500lfpm Continuous Surge Parameter Value -6.0 to 0 6.0 to 0 -6.0 to 0 6.0 to 0 50 100 -40 to +85 -65 to +150 190 130 41 to 44 5% 265 Unit VDC VDC VDC VDC mA C C C/W C/W C
* Maximum Ratings are those values beyond which damage to the device may occur.
DC BLOCKING CAPACITORS 75 0.1F EP89 75 150 150 0.1F 75 COAX 75 75 COAX 75
VEE
Figure 2. EP89 Termination Configuration
http://onsemi.com
2
MC10EP89
DC CHARACTERISTICS, ECL/LVECL (VCC = 0V; VEE = -3.3 0.01V) (Note 4.)
-40C Symbol IEE VOH VOL VIH VIL Characteristic Power Supply Current (Note 1.) Output HIGH Voltage (Note 2.) Output LOW Voltage (Note 2.) Input HIGH Voltage Single Ended Input LOW Voltage Single Ended Min 22 -1220 -2680 -1230 -1950 -1.3 Typ 28 -1120 -2580 Max 34 -1020 -2480 -890 -1500 0.0 150 D D 0.5 -150 0.5 -150 Min 24 -1150 -2670 -1130 -1950 -1.3 25C Typ 32 -1050 -2570 Max 38 -950 -2470 -810 -1480 0.0 150 0.5 -150 Min 28 -1075 -2630 -1060 -1950 -1.3 85C Typ 34 -975 -2530 Max 40 -875 -2430 -720 -1445 0.0 150 Unit mA mV mV mV mV V A A
VIHCMR Input HIGH Voltage Common Mode Range (Note 3.) IIH IIL Input HIGH Current Input LOW Current
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. 1. VCC = 0V, VEE = -3.3V, all other pins floating. 2. All loading with 50 ohms to VCC-3.0 volts. 3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. 4. Input and output parameters vary 1:1 with VCC.
DC CHARACTERISTICS, ECL/LVECL (VCC = 0V; VEE = -5.2 0.01V) (Note 8.)
-40C Symbol IEE VOH VOL VIH VIL Characteristic Power Supply Current (Note 5.) Output HIGH Voltage (Note 6.) Output LOW Voltage (Note 6.) Input HIGH Voltage Single Ended Input LOW Voltage Single Ended Min 25 -1220 -2950 -1230 -1950 -3.2 Typ 32 -1120 -2800 Max 39 -1020 -2650 -890 -1500 0.0 150 D D 0.5 -150 0.5 -150 Min 28 -1150 -2950 -1130 -1950 -3.2 25C Typ 35 -1050 -2850 Max 42 -950 -2650 -810 -1480 0.0 150 0.5 -150 Min 31 -1075 -2950 -1060 -1950 -3.2 85C Typ 38 -975 -2800 Max 45 -875 -2650 -720 -1445 0.0 150 Unit mA mV mV mV mV V A A
VIHCMR Input HIGH Voltage Common Mode Range (Note 7.) IIH IIL Input HIGH Current Input LOW Current
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. 5. VCC = 0V, VEE = -5.2V, all other pins floating. 6. All loading with 50 ohms to VCC-3.0 volts. 7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. 8. Input and output parameters vary 1:1 with VCC.
http://onsemi.com
3
MC10EP89
DC CHARACTERISTICS, LVPECL (VCC = 3.3V 0.01V, VEE = 0V) (Note 12.)
-40C Symbol IEE VOH VOL VIH VIL Characteristic Power Supply Current (Note 9.) Output HIGH Voltage (Note 10.) Output LOW Voltage (Note 10.) Input HIGH Voltage Single Ended Input LOW Voltage Single Ended Min 22 2080 620 2070 1350 2.0 Typ 28 2180 720 Max 34 2280 820 2410 1800 3.3 150 D D 0.5 -150 0.5 -150 Min 24 2150 630 2170 1350 2.0 25C Typ 32 2250 730 Max 38 2350 830 2490 1820 3.3 150 0.5 -150 Min 28 2225 670 2240 1350 2.0 85C Typ 34 2325 770 Max 40 2425 870 2580 1855 3.3 150 Unit mA mV mV mV mV V A A
VIHCMR Input HIGH Voltage Common Mode Range (Note 11.) IIH IIL Input HIGH Current Input LOW Current
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. 9. VCC = 3.3V, VEE = 0V, all other pins floating. 10. All loading with 50 ohms to VCC-3.0 volts. 11. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. 12. Input and output parameters vary 1:1 with VCC.
DC CHARACTERISTICS, PECL (VCC = 5.0V 0.5V, VEE = 0V) (Note 16.)
-40C Symbol IEE VOH VOL VIH VIL Characteristic Power Supply Current (Note 13.) Output HIGH Voltage (Note 14.) Output LOW Voltage (Note 14.) Input HIGH Voltage Single Ended Input LOW Voltage Single Ended Min 27 3780 2075 3770 3050 2.0 Typ 34 3880 2225 Max 41 3980 2375 4110 3500 5.0 150 D D 0.5 -150 0.5 -150 Min 30 3850 2060 3870 3050 2.0 25C Typ 37 3950 2210 Max 44 4050 2360 4190 3520 5.0 150 0.5 -150 Min 32 3925 2090 3940 3050 2.0 85C Typ 39 4025 2240 Max 46 4125 2390 4280 3555 5.0 150 Unit mA mV mV mV mV V A A
VIHCMR Input HIGH Voltage Common Mode Range (Note 15.) IIH IIL Input HIGH Current Input LOW Current
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. 13. VCC = 5.0V, VEE = 0V, all other pins floating. 14. All loading with 50 ohms to VCC-3.0 volts. 15. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. 16. Input and output parameters vary 1:1 with VCC.
http://onsemi.com
4
MC10EP89
AC CHARACTERISTICS (VCC = 0V; VEE = -3.0V to -5.5V) or (VCC = 3.0V to 5.5V; VEE = 0V)
-40C Symbol fmax tPLH, tPHL tSKEW tJITTER VPP Characteristic Maximum Toggle Frequency (Note 17.) Propagation Delay to Output Differential Duty Cycle Skew (Note 18.) Cycle-to-Cycle Jitter Input Voltage Swing (Diff.) (Note 19.) 150 200 280 5.0 TBD 800 1200 150 380 20 220 Min Typ Max Min 25C Typ 3.0 310 5.0 TBD 800 1200 150 400 20 250 330 5.0 TBD 800 1200 420 20 Max Min 85C Typ Max Unit GHz ps ps ps mV
tr Output Rise/Fall Times Q 120 230 380 130 250 410 150 270 430 ps tf (20% - 80%) 17. Fmax guaranteed for functionality only. 18. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the outputs. 19. VIL must not go below VCC - 3V.
http://onsemi.com
5
MC10EP89
PACKAGE DIMENSIONS
SO-8 D SUFFIX PLASTIC SOIC PACKAGE CASE 751-06 ISSUE T
A
8
D
5
C
E
1 4
H
0.25
M
B
M
h B C e A
SEATING PLANE
X 45 _
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_
q
L 0.10 A1 B 0.25
M
CB
S
A
S
q
http://onsemi.com
6
MC10EP89
Notes
http://onsemi.com
7
MC10EP89
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
USA/EUROPE Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line*: 303-675-2167 800-344-3810 Toll Free USA/Canada
*To receive a Fax of our publications
ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5487-8345 Email: r14153@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
N. America Technical Support: 800-282-9855 Toll Free USA/Canada
http://onsemi.com
8
MC10EP89/D

▲Up To Search▲

Price & Availability of MC10EP89

	To Download MC10EP89 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .